Відео

Only five things in creation that gun can’t kill

I inherited one of these recently, broke it down per your instructions and cleaned it up. The firing pin and bottom plate fought with me for about an hour popping apart each time I tried to get it back into the receiver. I also had the issue with the forearm ring wanting to cross thread. Finally put the forearm back on it and got it put back together that way. Not fun, would not recommend. Still going to shoot it though.

use a knife sharpener

You can extend the completed round exit chute by drilling a hole through a piece of sheet metal cut to the desired shape and use a bolt that fits into the unused threaded hole on the base of the Pro 1000 left rear, I did it and it works quite well.

The rough rider beats the hell out of this

You had me in the first sentence.

I only wish the 1875 was made with the same octagonal barrel profile the 1858 had.

Just picked mine up today. Dry as a bone. I had to oil it up right off the bat. Can't wait to try it.

It fits in a Recover Tactical P-IX 😁

Loved it kept the light on when I carried it for the day battery was very good

Yall know if they make this for 10 shot 22magnum?

Outstanding , thanks for educating us all

4:36 I found it easier to install the two-piece slide stop in two steps: first install the slide stop part without the pin/axle. Then, pull the slide stop piece backward so it compresses the plunger, and allow pin holes to line up, now insert pin. As for the Federal (and other weak and cheap ammo), on my unit which is a full size, if I use the original 23 lb hammer spring/main spring, only the CCI Mini Mag will work. When I changed the main spring to the included 18 lb one, all ammo expect the Federal worked. So, knowing it was the under-powered nature that caused malfunction, I replaced the main spring with the lightest I could find, Wolff 15 pounder, now Federal works almost completely. "Almost" because the first round of a fully loaded mag, occasionally will have hiccup. The extra pressure from completely compressed mag spring will create extra friction under the slide and cause it to not fully cycle :)

I had the same issue with my Kimber 1911 10mm target but with the factory grip safety. If I grip it really hard, there was no issue. But when I use a firm grip, it hangs up ever so slightly on the trigger and affects my trigger pull. By using the example on this video, I removed a slight amount of material on the grip safety with a coarse stone, and smoothed it out with a fine stone afterwards. The trigger pull is now as smooth as a glass surface. Thank you sir for this excellent video. Saved me a few bucks and a trip to the smith. Problem resolved.

Brother they came out amazing, the nicks n dings came out perfect. That is hard to do and alot of times it looks good but it just dont look genuine. They look like you robbed em from an original colt. Well done 👍

Do you have a spare loading tool for that? Mine didn't come with one

Why does Pietta stubbornly refuse to listen to their customers and make the 1861 with the correct length barrel?

can you have a felony to own one with the conversion?

If a hacksaw and file is historically accurate the. This is also! Lol

Got 1 two weeks ago. I’ve already put several hundred rounds to it. I haven’t had one single problem at all. I seriously think that you got should need to check this gun out.

Single handed, try holding the with less grip force. You are pushing the gun as power grip it, pushing the point of impact left and down ! Your two handed groups were awesome!

12” circle at 25 yards = combat effective!

Why do you prefer the 1860 Army over the 1858 Remingtons?

As historical as any firearm as long as the hacksaw and file were available! Gunsmiths did a lot of custom work back in the day especially pre 1990! Lol

Time to smoke some demons 👻

I got a bb gun of one of these. It surprised me to see that the bb gun is actually not some made up gun and was actually a real gun from the 1905

Very nice video I bought a stoeger str-9 9mm and luv it

That is truly a great piece with extraordinary details. Take care of it 👍

Your video just got recommended,.. So how's the pistol, you still have it?

Mags dont interchange with glock or sig. Apart of that after 1500 rounds, not even one jam. Eats all.

Just picked up my Remington #10 caps at Bass Pro shop! Order them online!!!

Shooting high isn’t always a bad thing, allows for better target visibility, not having to obscure a target to lob it in where you need it. As long as you know where it hits and it groups well, I prefer it grouping 4”-6” high

The police in Berlin used the P6 until 2018.

At the 16 minute mark... I use a half inch long piece of 5/32 in vacum line tubing, inserted into the bottom/center of the shell holder plate. It centers the rod, but does not cause any binding. Spray a little silicone spray on the rubber occasionally.

Did you do the barrel shortening yourself?

Lanyard, yes!

Can anyone tell me where to find d his video on making the modified loading lever? Have not seen any avenging angels with the loading lever slot so a 5 1/2 or 8 inch barrel needs to be cut down . Help! Lol

Not being familiar with BP I was quite surprised by the amount of unburned powder (sparks) at each shot.

Why add the cream of wheat? Have you tried paper cartridges?

Have you tried Uberti replicas?

I got two Super Wranglers for the money I paid . They are just fine for me, no they won't have the quality of the more costly Ruger. I enjoy mine.

Beretta 96 is the smoothest 40 cal

Big Iron on your hip!

Beautiful piece. I recently reposted my shooting video from last year after editing it of me shooting my Uberti 1858 new model army revolver using my Howell cylinder to shoot .45 Colt cowboy loads at an 8 inch terra cotta flower pot. I hope you enjoy it

I own the full size px4storm in 40 and a Gen 5 Glock 22, the gen 5 Glock 22 is softer shooting than the px4 storm

That's a very good deal. I paid $270 without optics but it did include the FFL fee.

Thank you for this video. I just purchased Mac 11 with a Lage upper. And it also comes with this .22 conversion kit. I can't wait to get my stamp.

Beretta 92FS all the way. Pre 2000's

Have any load data?

Awesome video, thank you 👍👍